卡特 crateCA6110DG 60瓦 木吉他 电箱琴吉他音箱 正品行货全新
- 品牌:crate
- 额定功率:51W(含)-100W(含)
- 扬声器个数:10个
- 价格区间:3001-10000元
NOTE: Channel 1 and Channel 2 are independent of each other up
to the Effects and Master sections. The text below (#1–8)
applies to both channels.
1: Input. The signal from a low impedance microphone or your acoustic
instrument may be connected here by means of a shielded, balanced
microphone cable terminated with an XLR connector or a shielded
signal cable. This combo jack has 15 volts phantom power applied to
XLR pins 2 and 3. (Mics not requiring phantom power will not be
affected.)
2: Gain. This serves as the input level control for the Input jack (#1). For
the best signal to noise ratio set this control so the Peak LED (#3)
flashes on strong signals.
3: Peak. This LED flashes when the signal level into the preamp
approaches clipping. Adjust the Gain control (#2) until a strong signal
causes this LED to flash.
4: Low. This serves as the bass control. Adjust this control to get the best
sounding bass response for this channel. Excessive boost of the low
control can cause an unnatural howling and should be avoided.
5: Mid. This serves as the midrange control. Adjust this control to get
the best projection and midrange tones for your instrument. The center
point of the mid control is chosen by the setting of the Contour
control (#6).
6: Contour. Use this control to set the center point of the Mid control
(#5). Set this control at the frequency which gives you the most natural-
sounding midrange tones.
7: High. This serves as the treble control. Adjust this control so your
high notes and harmonic overtones are lively but not overpowering.
8: DSP/Eff Send. Use this control to adjust the amount of internal
Digital Effect and/or external effect (if used).
The Master Section - part one:
9: CD Input. Use these RCA jacks to connect a CD or tape player to the
amplifier. Use the CD Level control (#10) to adjust the level of the
player.
10: CD Level. Use this control to adjust the signal level at the CD Input
jacks (#9).
11: Tweeter Cut. Use this control to reduce the output level of the internal
high frequency driver. In the fully counter-clockwise position, the
tweeter is at its full output level. As you rotate the control clockwise,
the tweeter level decreases. Adjust this control to best suit your playing
environment.
12: Feedback Filters. Use these switches to activate the CA6110D’s
advanced feedback elimination circuitry. For complete details, see the
section entitled “To Eliminate Feedback” on page 6.
The Effects Section:
13: Mode. Use this control to select the type of Digital Signal Processing
effect applied to the output signal. For a listing of the effects, please
see the section entitled “The DSP Section” on page 6.
14: DSP Level. Use this control to adjust the amount of internal DSP
effect.
The Master Section - part two:
15: Level. Use this control to set the overall output level of the amplifier.
16: Power. Use this switch to turn the amplifier on (top of the switch
depressed) and off (bottom of the switch depressed.) The power
switch illuminates when the amplifier is on.
17: External Speaker. Use this jack to connect the amplifier to an external
speaker cabinet. This jack is wired in series with the internal speakers
which remain active when an external speaker is connected.
18: Feedback Filters Footswitch. Connect the three-button footswitch to
this jack for remote control of the feedback filters. The Feedback
Filters ON LED (#12, front panel) illuminates and the feedback circuit
is activated when a footswitch is connected to this jack. Footswitch
button #1 controls Feedback Filter 1, button #2 controls Filter #2. (See
illustration below.)
Note: This is a STEREO jack: tip = Filter 1, ring = Filter 2, sleeve is
ground. Use only a footswitch equipped with a stereo 1/4” plug.
19: DSP A/B Bank Footswitch. Connect the three-button footswitch to
this jack for remote control of two DSP settings:
1.With footswitch button #3’s LED illuminated, select one of the DSP
settings
2.Step on footswitch button #3 - the LED will go out - select a different
DSP setting
3.Step on footswitch button #3 again - the LED illuminates, and the
DSP automatically changes back to the setting chosen in step 1.
4.Step on footswitch button #3 again - the LED goes out, and the DSP
automatically changes back to the setting chosen in step 2.
20: Effects Aux In/Eff Ret. When using an external signal processor or any
line level signal (drum machine, keyboard, etc), connect the output of the
device to this jack by means of a shielded signal cable.
21: Effects Send. When using an external signal processor, connect this
jack to the input of the effect by means of a shielded signal cable.
22: Line Out Level. Use this control to adjust the output level of the line
out signal. (This control works independently from the amplifier’s
master level control.)
23: High Z Bal Line Out. Use this jack to connect a high impedance, line
level signal to a house sound board, a recording console or an external
power amplifier by means of an 1/4” stereo plug-terminated
cable. (Ring is signal +, tip is signal -, and sleeve is ground.)
24: Gnd Lift. This switch, when depressed, electronically disconnects
both of the Line Out jacks’ (#23, #25) chassis ground connections. If
you experience excessive noise when using the Line Out jacks,
depress this switch.
25: Low Z Bal Line Out. Use this jack to connect a low impedance, line
level signal to a house sound board, a recording console or an external
power amplifier by means of an XLR-terminated cable. (Pin 1 is
ground, pin 2 is signal +, and pin 3 is signal -.)
26: AC Line Cord (not shown). The grounded power cord should only
be plugged into a grounded power outlet that meets all applicable
electrical codes and is compatible with the voltage, power and frequency
requirements stated on the rear panel. Do not attempt to
defeat the safety ground connection!
Technical Specifications:
Crate continually develops new products, as well as improves existing ones. For this reason,
the specifications and information in this manual are subject to change without notice.
Output Power Rating: 60 watts @ <1% THD
Channels 1 & 2: Low: +/-15dB @ 80Hz
Mid: +15, -30dBdB from 450Hz – 1.2kHz (Contour)
High: +/-15dB @ 10kHz
Input Impedance: 3.3M ohm High-Z, 3k ohm Low-Z
Input Sensitivity: 5mV High-Z, 2mV Low-Z
Sens. to Eff Send/Line out: 6mV High-Z, 3mV Low-Z
Max Input Signal: 6V RMS (17V peak to peak)
CD Input: Input Impedance: 22k ohm
Input Sensitivity: 150mV
Max Input Signal: 6V RMS (17V peak to peak)
AuxEff. Return: Input Impedance: 11k ohm
Input Sensitivity: 60mV RMS
Max Input Signal: 6V RMS (17V peak to peak)
Eff Send Out. Impedance: 2.2k ohm
Line Out Out. Impedance: 220 ohm Low-Z, 2.2k ohm High-Z
Feedback Filters: 10Hz to 4.8kHz range, -15dB cut per filter
Internal Woofer: 10” w/polypropylene cone, rubber surround, 30.5oz magnet, 1.5” voice coil,
8 ohms, 75w RMS, 95dB 1w 1m
Internal Tweeter: High efficiency Piezo, 110dB 1w 1m
Internal Crossover: Passive type
Power Requirements: 120VAC, 60Hz, 70VA
电压 100/115VAC, 50/60Hz, 70VA 230VAC, 50/60Hz, 70VA（中国）
尺寸与重量: 44x 40x 36厘米 ”17公斤
卡特十寸 扬声器
- 60 watts 持续功率输出
- Two channels 双声道输入
- Auto feedback elimination circuit 自动回受音消除
- 16 digital effects with level control 16种数字效果带水平控制
- RCA CD/MP3 input 可接入伴奏CD/MP3
- 有平衡线路输出 XLR
这些吉他手使用的都是卡特吉他音箱，希望可以参考
»Edsel Dope（Dope乐队）工业说唱金属类
»Mike Scaccia （Rigor Mortis乐队）重型金属乐类
»Sammy Hagar（Van Halen， Chickenfoot ， Hagar Schon Aaronson Shrieve，Montrose，等乐队）老炮类
»Freddy Castro （Riverboat Gamblers）车库朋克类
»Joe Walsh （老鹰乐队）乡村民谣类
»Shawn Smash（Total Chaos乐队） 朋克类
»C.C. DeVille （毒药乐队） 流行金属类
»Scott Hull （Gnomes of Zurich乐队）非主流 独立摇滚类
»Jake Kolatis & Rick Lopez OI 朋克类
»Fletcher Dragge （The T4 Project乐队 ，Pennywise乐队）硬核 朋克类
»Robert Randolph 布鲁斯类音乐
»Al Jourgensen （工业金属 内阁乐队等）
»Jerry Douglas 夏威夷吉他大师
»Bo Diddley 布鲁斯音乐
»Stan Lee （The Dickies）老牌美式朋克
点此回到所有卡特设备页面
热门设计服务
浙公网安备 33011002014641号